CF 2 1/4 CF2 1/4S CF2 1/4B NUTR 17A
Cam Follower Track Roller Bearing
1. The eccentric stud provides a way to adjust the radial position of the bearing, which can improve the load balance in the bearing combination application. The load balancing of the cam follower bearing can reduce premature damage due to bearing overload, thereby saving operating costs, reducing the requirements for precise mounting hole position tolerances, and providing the ability to readjust the bearing position as the raceway wears. The eccentric bushing is installed on the stud by press-fitting and is not hardened to keep the pin or set screw permanently locked.
2. The bushing type is also one of the MCGILL cam follower bearings. Non-metallic bushings support the load by sliding. For non-food-grade applications that are not convenient for relubrication or that do not allow grease contamination in the process, non-metallic bushings can reduce the bearing The need for lubrication. Its maximum allowable continuous operating temperature is 200 ° F. Bushed CAMROL bearings are used in a self-lubricating mode. However, continuous oil lubrication can be used to reduce wear rates. It should not be lubricated with grease.
Why Choose Us?
1. No MOQ, 1pcs ti is ok.
2. Supporting 7days refudn in case of bad qualty.
3. 24hours service
4. Welcome concat us for price list.
What kinds of payment terms do you offer?
1. Paypal is accepted.
2. Direct RMB is supported.
3. Payment online is supported.
4. Wester union is supported.
5. Less deposit is accpeted.
| CF KR SPECIFICATIONS |
| Model |
Weight |
d |
D |
C |
B1 |
B2 |
G |
G1 |
| No Seal |
Reference model |
(gram) |
mm |
mm |
mm |
mm |
mm |
mm |
| CF 3 |
KR10 |
4.5 |
3 |
10 |
7 |
17 |
9 |
M3X0.5 |
5 |
| CF 4 |
KR12 |
7.5 |
4 |
12 |
8 |
20 |
11 |
M4X0.7 |
6 |
| CF 5 |
KR13 |
10.5 |
5 |
13 |
9 |
23 |
13 |
M5X0.8 |
7.5 |
| CF 6 |
KR16 |
18.5 |
6 |
16 |
11 |
28 |
16 |
M6X1 |
8 |
| CF 8 |
KR19 |
28.5 |
8 |
19 |
11 |
32 |
20 |
M8X1.25 |
10 |
| CF10 |
KR22 |
45 |
10 |
22 |
12 |
36 |
23 |
M10X1.25 |
12 |
| CF10-1 |
KR26 |
60 |
10 |
26 |
12 |
36 |
23 |
M10X1.25 |
12 |
| CF12 |
KR30 |
95 |
12 |
30 |
14 |
40 |
25 |
M12X1.5 |
13 |
| CF12-1 |
KR32 |
105 |
12 |
32 |
14 |
40 |
25 |
M12X1.5 |
13 |
| CF16 |
KR35 |
170 |
16 |
35 |
18 |
52 |
32.5 |
M16X1.5 |
17 |
| CF18 |
KR40 |
250 |
18 |
40 |
20 |
58 |
36.5 |
M18X1.5 |
19 |
| CF20 |
KR47 |
460 |
20 |
47 |
24 |
66 |
40.5 |
M20X1.5 |
21 |
| CF20-1 |
KR52 |
385 |
20 |
52 |
29 |
66 |
40.5 |
M20X1.5 |
21 |
| CF24 |
KR62 |
815 |
24 |
62 |
29 |
80 |
49.5 |
M24X1.5 |
25 |
| CF24-1 |
KR72 |
1,140 |
24 |
72 |
29 |
80 |
49.5 |
M24X1.5 |
25 |
| CF30 |
KR80 |
1,870 |
30 |
80 |
35 |
100 |
63 |
M30X1.5 |
32 |
| CF30-1 |
KR85 |
2.03 |
30 |
85 |
35 |
100 |
63 |
M30X1.5 |
32 |
| CF30-2 |
KR90 |
2,220 |
30 |
90 |
35 |
100 |
63 |
M30X1.5 |
32 |
PHOTOS OF BEARINGS:
Cam Follower Needl Bearing :
The flange-type outer diameter (OD) of the cam follower can increase bearing life compared to standard cylindrical cam follower MCGILL bearings. Cams help distribute stress on the outer ring and rolling elements due to misassembly or stud bending. The cam also helps to reduce slippage of the outer ring in swivel or rotary applications. Not all applications take advantage of the flange outer diameter. Ask the application engineering department for guidance on your application.
Increasing the diameter of heavy-duty studs and the rod diameter of heavy-duty stud cam follower bearings increases the diameter of the studs, which can improve the static load carrying capacity of MCGILL bearings. Increasing the diameter can reduce the amount of deflection that can occur when the cam follower bearing is subjected to radial loads. Due to the increased load carrying capacity, the maximum recommended load can be 50% BDR. * On heavy-duty stud bearings, only for CFH inch series.
MCGILL bearings with hexagonal holes (reamed holes) are also available. The fixing force of the inner hexagonal holes is higher than the standard screwdriver slot, which is helpful for the installation and removal of stud cam follower bearings. Hexagonal characteristics are marked with "B" because it is produced by the reaming process. For sizes up to 3 ", bearing relubrication from the flange end must be considered.
FAQ
1.Q:How do you pack the bearing ?
A:It is ORIGINAL packaging.
It can be done as your specfic demands.
2.Q:Can I get some samples and do you offer the sample free?
A:Yes, sure, we are honored to offer you samples.If we have stock, we can send you free sample.
And you just need to pay freight. If there have no stock, you need to pay sample fee and freight.
3.:Does the sample fee can be return back?
A: If you place an order, we can return part of sample fee even all of fee to you.It also depends
on the Quantity of order and the type of sample.
4.Q:What is the MOQ for bearing?
A: Our MOQ is 1 pc.
5.What is the delivery time?
A:Generally in 2 days after payment.
According to the order amount or as your request.
6.Can you promise to deliver bearing hfl 3530 in time?
A: Credit always ranks the top on the list. We will absolutely deliver the goods in 2-4 days after your order is confirmed.
7.What is the payment item?
A:·100% Western Union or Paypal in advance ,specially for small amount
100% T/T or western union in advance for small quantity order
30%-70% T/T in advance, balance before shipment for large order or long delivery time orders.
Your message must be between 20-3,000 characters!
